Evaluation of dynamic modulus measurement for C/C-SiC composites at different temperatures

The determination of elastic properties at application temperature is fundamental for the design of fibre reinforced ceramic composite components. An attractive method to characterize the flexural modulus at room and high temperature under specific atmosphere is the nondestructive Resonant Frequency Damping Analysis (RFDA). The objective of this paper was to evaluate and validate the modulus measurement via RFDA for orthotropic C/C-SiC composites at the application temperature. At room temperature flexural moduli of C/C-SiC with 0/90° reinforcement were measured under quasi-static 4-point bending loads and compared with dynamic moduli measured via RFDA longitudinally to fibre direction. The dynamic modulus of C/C-SiC was then measured via RFDA up to 1250°C under flowing inert gas and showed an increase with temperature which fitted with literature values. The measured fundamental frequencies were finally compared to those resulting from numerical modal analyses. Dynamic and quasi-static flexural moduli are comparable and the numerical analyses proved that bending modes are correctly modeled by means of dynamic modulus measured via RFDA. The nondestructive RFDA as well as the numerical modeling approach are suitable for evaluation of C/C-SiC and may be transferred to other fibre reinforced ceramic composite materials.     

Developing high-performance laminated Cu/TiC composites through melt infiltration of Ni-doped freeze-cast preforms

Nacre-inspired laminated composites have been proven to possess a unique combination of strength and toughness. In this study, we fabricated nacre-mimetic Cu/TiC composites via unidirectional freezing of aqueous TiC slurries containing different amounts of NiO additives, followed by ice sublimation, carbothermal reduction of NiO to Ni during sintering and then gas-pressure infiltration of the Cu melt. The introduction of Ni greatly facilitated the densification of ceramic lamellae and enhanced the interfacial bonding between Cu and TiC. The resultant composites displayed outstanding damage tolerance and anisotropic electrical conductivities. Specifically, for an ～31?vol% TiC–Cu composite containing 24?wt% Ni in the ceramic lamellae (based on the TiC content), a fracture toughness (K_Jc) of 72.5?±?1.0?MPa·m^1/2, work of fracture of 53.4?±?3.5?kJ/m², bending strength of 725?±?11?MPa and longitudinal electrical conductivity of 22.7?MS/m (～60% of the Cu matrix) were achieved, which were approx. 81%, 536%, 122% and 97% higher than those of the Ni-free composite, respectively. Noticeable toughening was demonstrated to be a consequence of multiple cracking, plastic deformation and uncracked-ligament bridging of the metal layers, as well as crack deflection and blunting. On the other hand, significant strengthening resulted from tailoring the microstructures in the ceramic layers and at the Cu/TiC interface as a result of Ni doping. We believe that the facile strategy adopted herein provides an effective way to solve the problems of wetting and bonding related to metal infiltration and can be readily extended to the preparation of other nacre-inspired metal?ceramic composites.     

石墨烯增强钛基复合材料制备工艺与性能研究

以多层石墨烯为增强体,通过熔炼锻造(MF)和粉末冶金(PM) 2种工艺分别制备出规格为Φ10 mm的石墨烯增强钛基复合材料棒材。石墨烯在凝固过程中以TiC枝晶形态析出,变形后呈细小颗粒,其中Ti和C原子比约为2∶1。石墨烯和球形钛粉经过机械合金化和变形加工,在基体中反应形成薄片层。MF工艺对应的棒材拉伸强度可达476 MPa,延伸率保持在28%; PM工艺对应的棒材拉伸强度可达487 MPa,延伸率保持在30%。PM工艺可形成尺寸较小的薄片状石墨烯增强体,强化作用提升,同时塑性没有显著下降。     

Investigation of non-isothermal crystallization,dynamic mechanical and dielectric properties of poly(ether-ketone) matrix composites

ABSTRACT

Poly(ether-ketone)/hexagonal boron nitride (h-BN) composites reinforced with micrometer-sized h-BN particles were investigated. The composites exhibited glass transition temperature (T_g) and thermal stability over 160°C and 560°C, respectively. The melting point and peak crystallization temperatures of the composites decreased up to 17°C and 12°C, respectively. The linear CTE of the composites decreased both below and above the T_g. The storage modulus increased with increasing h-BN content at all temperatures (50–250°C). The composites possessed excellent dielectric properties with insignificant dispersion with increasing frequency. Thus, resultant composites are promising candidates for the printed circuit boards/electronic substrates.     

Thermal and dynamic mechanical behavior of epoxy composites reinforced with post-consumed yerba mate

Yerba mate (YM) is widely consumed in Latin American countries, and its residues can be used as bio-resources such as reinforced in epoxy composites. The present work aims to produce epoxy resin composites and evaluate the influence of post-consumed YM as reinforcement. The concentrations of YM used were 5, 10, and 20% (wt/wt). Chemical, thermal, morphological, and dynamic mechanical behaviors were explored. The YM incorporation did not influence chemically on the epoxy structure and a pull-out phenomenon was observed as YM content increased. The YM at lower concentrations (5 and 10%) led to higher values of activation energies calculated from model-free isoconversional methods. On the other hand, the composite e/YM 20 wt% improved all dynamic-mechanical properties. YM proved to be a suitable and cheap reinforcement for epoxy resin.     

Wear and thermal behavior of basalt fiber reinforced rice husk/polyvinyl chloride composites

Plant fiber reinforced polymer composites (PFRPs) in practical application are often subjected to both complex friction and variable temperature environments. The present work explores the possibility of reinforcing rice husk/polyvinyl chloride (RH/PVC) composites with basalt fibers (BF) for developing a new wear resistant material with improved thermal stability. The results showed that the structural strength and wear resistance of the composites increased at first and then decreased with an increasing ratio of BF/RH, the highest value occurred at a BF/RH ratio of 8/42. The thermal stability of composites had a positive relationship with BF/RH ratio. The composites added with BF all possessed improved performance in comparison with unadded composites. Hence, the findings of this article proposed some new perspectives on improving the wear resistance and thermal stability of PFRPs that would broaden their practical application.     

Constitutive model and failure criterion for orthotropic ceramic matrix composites under macroscopic plane stress

To predict the nonlinear stress-strain behavior and the rupture strength of orthotropic ceramic matrix composites (CMCs) under macroscopic plane stress, a concise damage-based mechanical theory including a new constitutive model and two kinds of failure criteria was developed in the framework of continuum damage mechanics (CDM). The damage constitutive model was established using strain partitioning and damage decoupling methods. Meanwhile, the failure criteria were formulated in terms of damage energy release rate (DERR) in order to correlate the failure property of CMCs with damage driving forces, and the maximum DERR criterion and the interactive DERR criterion were suggested simultaneously. For the sake of model evaluation, the theory was applied to a typical CMC with damageable and nonlinear behavior, that is, 2D-C/SiC. The damage evolution law, strain response and rupture strength under incremental cyclic tension along both on-axis and off-axis directions were completely investigated. Comparison between theoretical predictions and experimental data illustrates that the newly developed mechanical theory is potential to give reasonable and accurate results of both stress-strain response and failure property for orthotropic CMCs.     

Structural,ferroelectric, magnetic and magnetoelectric properties of (1-x) Ba0.85Ca0.15Zr0.1Ti0.9O3 -x La0.67Sr0.33MnO3 lead-free magnetoelectric composites

The influence of an additional La_0.67Sr_0.33MnO₃ (LSMO) magnetic phase on the structural, ferromagnetic, ferroelectric, and magnetoelectric properties of Ba_0.85Ca_0.15Zr_0.1Ti_0.9O₃ (BCZT) ferroelectric phase was studied for composites of (1-x)BCZT -xLSMO (x = 0, 25, 50, 75 and 100%). The ferroelectric BCZT sample showed a perovskite single phase formation with a tetragonal crystal structure of the P4mm space group, and the magnetic phase of LSMO presented a rhombohedral crystal structure of R3c space group as shown by XRD. The composite sample with 25% LSMO exhibited large ferroelectric and piezoelectric properties with remnant, saturation polarization, and coercive electric field P_r ~7.74 μC/cm², P_s ~11.69 μC/cm² and E_C ~12.22 kV/cm with a piezoelectric coefficient d₃₃ ~ 231 pC/N. The magnetic characterization for the composites showed that the sample containing 75% of LSMO revealed the highest remnant, saturation magnetization, and coercive field of M_r ~1.358 emu/g, M_s ~19.17 emu/g, and H_C ~33.19 Oe, respectively. Moreover, it revealed the largest magnetoelectric coupling coefficient α_ME ~2.51 mV/cm.Oe with high coupling quality at a lower applied magnetic field. The results highlight the value of these composites as lead-free room temperature magnetoelectric sensors and actuators.     

Effect of carbon nanotubes grown temperature on the fracture behavior of carbon fiber reinforced magnesium matrix composites: Interlaminar shear strength and tensile strength

The design of an interfacial structure is particularly important for load transfer in composites. In this paper, different amounts of carbon nanotubes (CNTs) were grafted onto the carbon fiber (CF) surface by adjusting grown temperature using injection chemical vapor deposition (ICVD). The prepared CF preform grafted with CNTs (CNTs-CF) were used to reinforce magnesium alloy by squeeze casting process. The microstructures were analyzed by means of optical microscope (OM) and scanning electron microscope (SEM), and the interlaminar shear strength (ILSS) and tensile strength of the composites were determined by double-notch shear test and tensile test. The results indicated that moderate ILSS was more conducive to improving the tensile properties of carbon fiber reinforced magnesium matrix (C_f/Mg) composites. Compared with C_f/Mg, the tensile strength of composite with CNTs increased by about 80%. For C_f/Mg composites grafted with CNTs, CNTs had the effects of delaying crack propagation and increasing energy consumption by the pull-out and bridging mechanism, which were the main reasons for improving the strength. The analysis of shear fracture surface showed that the crack propagation path can be optimized by adjusting the amounts of grafted CNTs. The presence of CNTs affects the stress distribution and consequently the crack initiation as well as the crack propagation.     

Formation of SiC whiskers/leucite-based ceramic composites from low temperature hardening geopolymer

In this study, SiC whiskers (SCWS) reinforced geopolymer composites (SCWS/KGP) and their ceramic products (SCWS/leucite) were prepared, and effects of SiC whiskers contents on the microstructure and flexural strength of the SCWS/KGP and SCWS/leucite composites were investigated. The results show that the whisker addition has little influence on both phase composition and thermal shrinkage of the KGP composites, but a suitable content of whisker will result in the improved flexural strength, and when the SCWS content is 2 wt%, flexural strength of the SCWS/KGP composite is enhanced by 95% compared with the neat geopolymer. The flexural strength of the composites can be further enhanced significantly after the composites being treated at 1100 °C and 1200 °C and flexural strength of the composite with SCWS content of 2 wt% was 107% and 125% higher than the untreated counterpart, respectively. The increase in flexural strength of the composites should be attributed to the strong leucite formation, whisker debonding and pulling out from matrix during the fracturing process based on the good interfacial bonding state between whisker and leucite matrix.